DIY HDMI HD Field Monitor For Under $450

I finished this bad boy 4 months ago and I am now finally getting around to the blog post. Hopefully this post is still a economically viable option considering how fast things like this come down in price. The unit has a very sharp image and runs over an hour off a small Li Ion battery. And yes, technically it's not HD, at 8.9" it's 1024x600, but it's a huge improvement regardless.

The story begins with my JVC GY-HM100u. I love this little camera, but it definitely has its quirks. One of its downsides is a tiny LCD screen. JVC could have bumped it up a tad even considering how small the camera is. The focus assist feature is however very nice and gives you sharp red highlights that indicate focus, but it still leaves me wanting more, especially in bright conditions. The LCD also lacks safe zones and horizon lines, so I was always shooting crooked. On top of all this, I'm getting into 35mm lens adapters using SLR lenses with manual focus only. This field monitor helps me see all my issues before they become problems.

I originally was considering an iKan V8000 HDMI model but the $800 price tag was hard to slip past the accountant. After Googleing around a bit, I found a tutorial here that explains how to build one yourself. Using this as my jump off point, I proceeded to purchase my components. I bought a 8.9" Brightview Kit w/MST control board ($225) from www.manhattanlcd.com and an economy Manhattan LCD Li-Ion battery ($69) and a short 3' HDMI cable ($9) to go with it. I would reccommend getting your LCD components first so you can measure them and order the correct size picture frame. Here is a couple shots of the raw components.

Once I had the screen components, I quickly noticed that the control board was wider than the screen itself. This meant the frame had to be ordered  wider and I would have to frame the screen much like a mat on a picture frame. When I measured the board to order the frame, I went ahead and added 1/4" to my measurements just to be safe (and I'm glad I did). I went with a Black Metal SuperCanvas frame 9-1/2 x 6-1/4 x 1-3/4 frame from www.pictureframes.com ($17.20).

Once the frame arrived, I quickly tried putting all the pieces together to make sure everything was going to fit. Next, I drew up a diagram of how the parts come together. 

The first task I decided to tackle was drilling the holes in the frame for the a/v inputs and control buttons. 

To get the holes in the right places, I placed the a/v connectors on the scanner, and cleaned them up with a drawing app. 

I printed my templates out and cut them out with an art blade, taped it to the frame and used a silver sharpie to transfer the shapes onto the frame. Using a drill press, I drilled out what I could and then used a dremel tool to clean up and shapes. After a lot of back and forth, my a/v connectors fit through the frame nicely. For the control buttons, I stumbled across a great solution here using modified push pins. I found some metal push pins and using the dremel tool, cutt off the ends and pins.

Once my holes were ready and my buttons complete I mounted the control board to the frame. If you look closely you'll see I even added a small green piece of green plastic (I snipped the end of my son's lego man light saber...thanks B!) positioned directly on top of an LED on the control board. I guess this is the power indicator light or something?

 The next task up for grabs was the spacer or mat that I needed to put around the panel to compensate for the oversized circuit board. I could have made this out of wood, plastic, cardboard, etc. but I used this handy material called Alumilite I think. It's two thin sheets of aluminum with a pvc core. Alumilite is used as a printing material for high end signs. The last company I worked for had a lot of these old signs laying around so I'm putting them to good use once again. I measured the inside edges of the frame to get my outer dimensions of my mat, and measured the LCD panel to get the size of the opening I needed to cut. Here is the mat cut out and with the LCD panel installed. Used some good ol' gaffers tape to hold the panel in place.

With my LCD panel secure, I am ready to frame it up. I reconnected the LCD panel to the circuit board, and slid the whole enchilada together just like I was framing a picture, minus the glass of course. Although, on a side note, I did buy a piece of UV coated glass to protect the LCD screen, but honestly it wouldn't fit and it seemed to scratch really easily.


So with the unit all closed up, I now had to figure out how to mount this sucker to my camcorder. After searching around for parts and pieces to make something, I decided to cave and just buy a monitor arm. I went with the IKan MA101 ($69.99). I'm really glad I did too, the arm is built very well for being so reasonably priced. To attach the arm to the monitor, I used the little screw-ins that came with the picture frame. Normally you would put a wire across these to hang the picture, but I mounted a scrap piece of aluminum I had laying around with some nuts and bolts and drilled a hole in the center to attach the monitor arm. I used a wing nut here so I can easily mount and unmount in the field without the need for tools. I also added a few strips of velcro to the backside of the frame to attach the battery. The velcro holds pretty good, but I fear a good knock could send it flying.


Here is a shot of the panel in action. (Coming Soon!)


My camera dosen't have an image flip option (Unlike the HM700) so when I use the lens adapter I simply mount my LCD upside down! (Coming Soon!)


It only took me an additional 8 weeks to write this blog, and now I'm considering turning this into a vlog.

THE LERBERG RIG

So I was at Comic-Con San Diego shooting promo video for local Poken affiliate and I knew I would be running around all day and didn't want to shlep the tripod, so I decided to debut my DIY steadycam (an Ikea CD shelf). Even though it wasn't quite finished I didn't want to try and go handheld, my JVC HM100 is tiny and shaky as all get out. I have been eyeing the manfrotto fig rig and when my wife brought home some CD shelves from Ikea for me to organize my office, I held it in my hands and it felt like it was meant to be. I immediately started running around the house with the CD rack and quickly realized this could work...

Fist step was to knock out the center support with a rubber mallet.

Next I decided which side would be the bottom (icoinflip) and using a 3/8" bit drilled a hole dead center for the counter weight mounting hole. The counter weight is just a 2.5 lb. weight from a weight set that can be found at any sporting goods store or just go take one from the weight set in your garage that you never use :)

I went to the Depo and picked up a 3/8" threaded 12" rod and some nuts, lock washers and a wing nut for the bottom. Here's what it looks like with counter weight attached.



Next step is the camera mounting plate. I really spent a lot of time thinking about how to best mount the camera on this thing. The bolt popping up from the counter weight was making it tricky. Then one day my wife and I are cleaning out the garage and she hands me these bracket/plate things to throw away and I had another ah ha moment. Apparently this plate is supposed to be used with the expedit shelves to attach it to the wall?

Here is a shot of the plate. I immediately (well after finishing the garage of coarse and like 3 days later, but mentally it was immediately) got the faithful dremel tool out and began chewing out a slot for my mounting screw. It could be cleaner, but you want to make sure your screw can enter the hole but won't fall out the slot. Here is a detail of the slot (twss). One thing I forgot to photograph was the square pad of craft foam I spray mounted around the slot so that the camera has a soft compressible surface to sit on so it won't jiggle loose with use. So here it is with the plate attached.

After that I cut some strips of the craft foam and spray mounted then to the handles. Then I used good ol' gaffers tape to finish it off. I drilled some holes in the top of the rig to facilitate mounting equipment like LCD screen, lights, mic receiver, etc. I bought some of these screw on hot shoe mounts from B&H to use with hot shoe accessories. Now lets load it up! Next, I will post a link to some split screen footage showing with and without the rig......